Home
021-58386189
Menu
Construction Aggregate Calculator. Enter the width, length, thickness, and product density and hit the "Calculate" button to calculate your estimate. If you do not know the product density, use the optional density estimator* or contact a local sales representative.
Get Price
Gravel Prices Per Ton. Bulk crushed stone and gravel prices are $10 to $50 per ton on average. Road base costs $18 to $30 per ton, and plain pea gravel or limestone costs $28 to $45 per ton.Buying gravel in small quantities costs over $100 per ton.It takes 1.4 tons of stone per cubic yard.
Get Price
For chest CT, the aggregate percentage difference between E DLP and E ICRP was 21% (1.4 vs 1.1), with a maximum difference of 83% (2.2 vs 1.2) for the patient population weighing less than 7.5 kg. E DLP corrected was calculated, correcting for CTDI measurements made in a 16-cm diameter phantom for patients weighing 0–9.4 kg and for patients ...
Get Price
Crushed aggregate, one-inch crushed concrete, recycled asphalt, 3/8-inch pea gravel, 2-inch sewer filter rock, and concrete and asphalt aggregate blends all weigh in at 1.07 tons. Pit run gravel follows at 1.25 tons per cubic meter, regardless of whether it is 2-inch or 4-inch.
Get Price
Tel. Phonenumber Fax. 850 273 5707 Gravelshop.com Sand Group USA inc. 5730 SW 23rd St Miramar, FL 33023 Established 2012
Get Price
Apr 04, 2012· D. Sichen, in Fundamentals of Metallurgy, 2005. 9.5.1 Slag–metal mixing. In steelmaking, slag–metal mixing is a very common phenomenon and it occurs due to the shear at the slag–metal interface caused by excessive liquid steel flow. 37 This mixing leads to emulsification of steel in slag, which increases the total interfacial area and consequently the rate of slag–metal reactions.
Get Price
Asphalt Mixtures Calculator. Enter the width, length and thickness, then hit the "Calculate" button to calculate your estimate. You may also revise the default density value of 145 lbs/cubic ft. Actual densities may vary depending on the components of the mix.
Get Price
2.6 Aggregate Crushing Value (ACV) BS812:Part 110:1990 2.7 Ten Percent Fines Value (TFV) BS812:Part 111:1990 2.8 Aggregate Impact Value (AIV) BS812:Part 112:1990 2.9 Los Angeles Abrasion Test (LAA) ASTM C535-89 2.10 Sodium Soundness Test (SSS) ASTM C88-90 2.11 Slump Test BS1881:Part 102:1983 2.12 Making of Concrete Test Cubes BS1881:Part 108:1983
Get Price
The ratio of fine to coarse aggregate is chosen as usual as 1:2. From the above table we know we need 250kg of total dry aggregate for our concrete. The general ratio of fine aggregate to coarse aggregate is 1:2, but it can be adjusted between 1:1.5 to 1:2.5 based on the grading of fine aggregate and size of coarse aggregate. Sand = 1 Part
Get PriceFor concrete with nominal maximum size of aggregate greater than or equal to 1.5 inch[37.5 mm], the preferred minimum core diameter shall be,three times the nominal maximum size of coarse aggregate but it should be at least two times the nominal maximum size …
Get Price
(10) where GM is specific gravity based on volume at moisture content M. Equation (10) is substituted into Equation (9) for moisture contents <30 percent and into Equations (3) and (4) for moisture contents >30 percent. Table 5 is a density table for specific gravity based on volume at 12 percent moisture content (GM = G12) 3
Get Price
M10 M15 M20 etc. are all grades of concrete, The 'M' denotes 'Mix' followed by a number representing the compressive strength of that mix in N/mm^2. A mix is a ...
Get Price
Oct 11, 2019· Following the primary-crushing stage, screens with two or three decks and different opening sizes separate the aggregate material into different size categories – with conveyors transporting the sized material for further crushing or stockpiling as a saleable product. Usually this screening is accomplished through dry screens.
Get Price
Association) formula to determine screen capacity. The twelve factors used in the formula below are based in large part on the VSMA charts and formula. Formula: A = B * S * D * V * H * T * K * Y * P * O * W * F "A", the calculated capacity per square foot of screen area in tons per hour. B = Basic capacity per square foot in tons per hour
Get Price
The densities (pounds per square foot, or tons per cubic yard, sometimes called "pounds per foot" or "tons per cube") will also vary according to the season, the saturation levels (dampness) of the piles of medium when you purchase the mediums, the quality of the sieves used to sort the crusher …
Get Price
Crusher run Aggregate CR-6 D 2940 (h) 6 12 - - - - - 15 50 - Bank Run Gravel – Subbase D 2940 9 12 - - - - - - 50 - ... In areas exposed to traffic manufactured sand shall have a minimum ultimate polish value of 8, based on the parent rock. (e) 5.0 for concrete not subject to surface abrasion. (f) Fine aggregate conforming to M 6 may be used ...
Get Price
Convert your density to lb/yd 3. 85 lb/ft 3 = 2295 lb/yd 3 (1 pound per cubic foot equals 27 pounds per cubic yard) If you're in the US, divide 2295 by 2000 (there are 2000lb in a US ton). If you're in the UK, divide by 2200 (there are 2204.62 lb in a metric tonne)
Get Price
May 03, 2018· Most gravel and crushed stone products have similar weights per ton. A general rule of thumb when converting cubic yards of gravel to tons is to multiply the cubic area by 1.4. For your reference, gravel typically weighs 2,800 pounds per cubic yard. In …
Get Price
10/11/2012 13 Road Aggregate 101: Handy Formulas for Field and Office Converting cubic yards to tons of: Large Open Graded Aggregate (AASHTO 1, Rip-Rap) = yd³ x 1.4 Well Graded Aggregate (2A, 2RC) = yd³ x 1.5 Driving Surface Aggregate or TSA = yd³ x 1.55 Shale = …
Get Price
Convert 200 cubic feet to cubic yards = 200/27 = 7.4 cubic yards 7.4 cubic yards * 1.237 = 9.15 cubic yards. This 9.15 cubic yards can then be used as an "ESTIMATED" amount of material needed for this job. And that is an "ESTIMATED Amount"! Reset Search. Material Swell/Bulking % …
Get Price
About US
Products
Case
Project
Contact
Online Chat
Sales Hotline